360 Q5 Enable Developer Option and USB Debugging

In this post, you will learn how to enable developer options and USB debugging on your 360 Q5. If you wanna connect your phone with a Computer or Laptop, make sure that USB debugging must be enabled on your 360 Q5. No doubt that enabling USB debugging was very easy in the previous version of Android devices. But now enable USB debugging is too difficult on the latest phones. Here we will guide step by step, how to enable developer option and USB debugging on Q5.

360 Q5 Full Specifications

360 Q5 smartphone is powered by Android 6.0 Marshmallow OS) which runs on GSM / HSPA / LTE technology. This device was released on 22 August 2016. The Latest Q5 comes with 128GB internal memory with 4GB ram and device screen size is 5.5 inches, 96.2 cm2 (~82.2% screen-to-body ratio and 1080 x 1920 Pixels, 24 bit color depth resolution.

The device comes with Dual 13 Megapixels + 12 Megapixels Autofocus, LED flash rear camera, and 13 Megapixels 30fps selfie camera. 360 Q5 is powered by Mediatek MT6771 chipset with Octa-Core (4×1.8GHz ARM Cortex-A72 + 4×1.4GHz ARM Cortex-A53) CPU and GPU is Adreno 510, 550MHz.

The 360 Q5 has a Non-removable Li-Po 3200 mAh battery and Connectivity options are Wi-Fi 802.11 a/b/g/n/, Dual Band, Wi-Fi Direct, 4.1, A2DP, LE bluetooth, A-GPS, Type-C USB v2.0, With Charging and Mass Storage Function and sensors are Proximity Sensor Accelerometer Ambient Light Fingerprint Compass Gyroscope Hall.

Download Latest 360 Q5 USB, Drivers

360 Q5 Secret Codes to unlock hidden features

How to enable developer mode in your 360 Q5

Today we will share with you very simple steps, you may easily enable or activate hidden developer mode using system settings on any Android device. Please read carefully all steps and before doing anything else, you need to create a backup your Android phone.

01: First of all, Go to settings ->>> select system settings. See the below image:

How to enable developer mode step 1 System settings

02: Now on your 360 Q5 device jut Go to ->>> About Phone. See the below image:

step 2 click on about phone option

03: After that, Scroll down of screen, and find the Build Number your 360 Q5 Press it 7 to 10 times. See the below image:

How to enable developer mode step 3 select Build number 7 to 10 times

04: After a few minutes 360 Q5 Now, you will see this a pop-message: You are now a developer! See the below image:

How to enable developer mode

05: Now Click on ->>> Back Tap Button and you will see developer options under system settings. See the below image:

Turn on hidden developer options

First of all, you must remember one thing, if your 360 Q5 turns off during the developer option. We always advise you that follow the above steps again to enable in your device.

How to Enable USB debugging on 360 Q5

You can transfer your Q5 all images, videos and, other documents to your Computer Using Enable USB debugging Mode Option.

01: Go to Settings on your 360 Q5 smartphone .

02: Now, Select From Settings option ->>>> About phone then Select ->>>> Software Information.

03: After that, Scroll Down screen and, Tap the Build Number on your Q5, now Tap the Build number 7 to 10 times, and you will see a message that says “Developer mode has been enabled”. Now you will see the messages “Allow USB Debugging”, click “OK”.

Now, you have successfully enabled USB debugging mode on 360 Q5

Related Posts:

Note We are 24/7 available to support you, if you feel any trouble or find any mistake contact us in the below comment section. You can comment on us anytime about 360 Q5 if you have any problems during enabling USB debugging.
If anything goes wrong the author or getdroidpro.com is not responsible for it.

Leave a Comment

Your email address will not be published.