Connect
To Top

360 N4s Enable Developer Option and USB Debugging

In this post, you will learn how to enable developer options and USB debugging on your 360 N4s. If you wanna connect your phone with a Computer or Laptop, make sure that USB debugging must be enabled on your 360 N4s. No doubt that enabling USB debugging was very easy in the previous version of Android devices. But now enable USB debugging is too difficult on the latest phones. Here we will guide step by step, how to enable developer option and USB debugging on N4s.

360 N4s Full Specifications

360 N4s smartphone is powered by Android 6.0 Marshmallow which runs on GSM / UMTS / CDMA / LTE technology. This device was released on 22 July, 2016. The Latest N4s comes with 32GB internal memory with 4GB ram and device screen size is 5.5 inches and 1080×1920 Pixels, 24 bit color depth resolution.

The device comes with 16 Megapixels with LED Flash rear camera, and 8 Megapixels with Aperture F/2.0, HDR selfie camera. 360 N4s is powered by MediaTek Helio X20 MT6797M chipset with Deca-Core 2.0GHz ARM Cortex-A72 + 2.0GHz ARM Cortex-A53 + 1.4GHz ARM Cortex-A53) CPU and GPU is ARM Mali-T880 [email protected] MHz, Quad-Core.

The 360 N4s has a Non-Removable Lithium-Polymer 5000 mAh battery with Fast Charging and Connectivity options are Wi-Fi 802.11 a/b/g/n/ac (5.0GHz), Wi-Fi Direct, Dual Band, 4.1 with A2DP bluetooth, A-GPS, GLONASS, microUSB 2.0, USB Host and sensors are Accelerometer, proximity, compass.

Download Latest 360 N4s USB, Drivers

360 N4s Secret Codes to unlock hidden features

How to enable developer mode in your 360 N4s

Today we will share with you very simple steps, you may easily enable or activate hidden developer mode using system settings on any Android device. Please read carefully all steps and before doing anything else, you need to create a backup your Android phone.

01: First of all, Go to settings ->>> select system settings. See the below image:

How to enable developer mode step 1 System settings

02: Now on your 360 N4s device jut Go to ->>> About Phone. See the below image:

step 2 click on about phone option

03: After that, Scroll down of screen, and find the Build Number your 360 N4s Press it 7 to 10 times. See the below image:

How to enable developer mode step 3 select Build number 7 to 10 times

04: After a few minutes 360 N4s Now, you will see this a pop-message: You are now a developer! See the below image:

How to enable developer mode

05: Now Click on ->>> Back Tap Button and you will see developer options under system settings. See the below image:

Turn on hidden developer options

First of all, you must remember one thing, if your 360 N4s turns off during the developer option. We always advise you that follow the above steps again to enable in your device.

How to Enable USB debugging on 360 N4s

You can transfer your N4s all images, videos and, other documents to your Computer Using Enable USB debugging Mode Option.

01: Go to Settings on your 360 N4s smartphone.

02: Now, Select From Settings option ->>>> About phone then Select ->>>> Software Information.

03: After that, Scroll Down screen and, Tap the Build Number on your N4s, now Tap the Build number 7 to 10 times, and you will see a message that says “Developer mode has been enabled”. Now you will see the messages “Allow USB Debugging”, click “OK”.

Now, you have successfully enabled USB debugging mode on 360 N4s

Related Posts:

Note We are 24/7 available to support you, if you feel any trouble or find any mistake contact us in the below comment section. You can comment on us anytime about 360 N4s if you have any problems during enabling USB debugging.
If anything goes wrong the author or getdroidpro.com is not responsible for it.

Leave a Reply

Your email address will not be published. Required fields are marked *